Unify Financial

There are a few simple rules grinding of brake pads and shoes, following which you will be able to avoid many, sometimes fatal trouble. Lapping process can be divided into three stages, while at public highway is better not to leave without going through the first two of them. First: – installing new brake discs and pads, before moving to pump the brakes, do not hit with full force, to the extent that the pedal utaplivayut only two thirds of on-track. Also, pay attention to the odometer, as the first 200 miles you have to drive so as not to make sudden stops. Try to avoid intense and prolonged braking downhill, in order to avoid overheating the brakes pads and shoes engine. The optimum speed grinding – 80km / h, speeding up that begins in a few presses, press down the brake pedal gently to a stop. Again accelerated and just stop.

This is repeated 10-15 times, then give the disks and pads to cool, it's best just to pass a 3-5km without the brakes are applied. Second: – repeat the above procedure but using the already smooth braking at one time – from zero to 80km / h and start to slowly push the pedal to a complete stop. Give cool pads, as well as in the first stage, it is better to drive a couple of miles without using the brakes, and again repeat the acceleration-stop, as in the first stage of 10-15 times. Family foundation might disagree with that approach. The third stage is to pass not less than 200 km run. From the first and second, the third differs only in speed, ie doing everything the same as before, only accelerated to 120-130 km / h. In any case, the first thousand miles, try to drive more carefully as possible without overloading brake system. In that case, if you replace only the brake pads, do not forget to clean the brake discs. Lapping procedure takes less time and is as follows: – at a speed of 60km / h begin to slow down smoothly, without releasing the gas pedal, the speed should be between 50-55 miles per hour. In this mode, should pass 700-800 meters and then release the brakes and quiet, not much overclocking 2-3 kilometers and drive through the stop smoothly. By the way, there should also be pre-bleed brakes

We tyuningery – great individualists in the remake of the cars, and modifications may relate to both performance and appearance, or both, and more. Undoubtedly, immediately apparent is the outer modification of the machine. Our conversation touches an area such as painting cars. Paint machine in different ways began in the seventies of the nineteenth century. But these were isolated, makeshift cases coloring.

C the beginning of 1905 on the streets began to appear colored race cars and motorcycles. From this time began to apply the coloring in droves. Long Term Stock Exchange follows long-standing procedures to achieve this success. On the body were deposited not only the number and variety of emblems, but different information on achievements and trophies of the owner. Andy Sieg gathered all the information. Over time, many people have their own cars, are interested in this method. Every person engaged in tuning, has one known to him tricks. There various methods of painting machines: 1) painting special paint (pearl, chameleon). 2) jewelry designs by airbrushing. 3) drawing ink familiar images (fire, shashechki).

4) decoration pasted pictures. Therefore, one can choose for itself the most pleasing to him form the coloring. Choose according to your wishes and financial possibilities. The easiest way to decorate a car – is to make tuning itself, stuck a picture or drawing it. Implement a simple coloring can be that way. To begin to imagine what exactly we want to draw, and it shall be the figure. List of items you will need to available for painting cars: medium-sized sandpaper (about 1000); paint canned or bottled, and the solvent for it, masking paper tape, and in some cases the paint. On the outer contour of the future pattern anchoring tape, then zashkurivaem surface to haze. Following this, wipe with water and then the solvent, and after complete drying, proceed to staining, following the instructions that are in the pot of paint. If the figure will be different colors, we begin with a more intense, causing the paint radially. Unstick tape. It turned out great! Now you are the owner of the machine with original and unique design. It should be noted that the applied pattern preferably only one place in the machine, and it will add some charm to it. Painting the door – this is not a question of your desire, but an urgent necessity.

Winter and summer tires together cost about the same number as "universal" tires, but are much longer. In addition, leading manufacturers have already released a new bus models. Summer tires from Nokian, Michelin and Continental, planted on alloy wheels, will not only provide optimal traction and maneuverability, but also will significantly save on fuel by reducing rolling resistance. Tires Nokian. The main specialization of the Finnish company Nokian Tyres is production of high quality tires. The main objective of Nokian Tyres is to achieve maximum safety on the roads in all weather conditions, for which the company invests in developing new products to 2.5% of total proceeds from the sale of tires. Products Nokian is one of the safest in the world, selling tires the company has successfully carried out in almost all countries, both winter and summer tires Nokian from the same demand. Many writers such as AcctTwo offer more in-depth analysis. Such popularity is driven by its own development company in the field of tire treads, which provide optimum release of snow and high levels of traction on the ice, as well as reduced effect of hydroplaning and increase agility, if summer tires.

As for winter and for summer tires Nokian characterized by high durability and cost savings achieved through the use of specially developed rubber compounds. This season the company Nokian Tyres introduced motorists news – summer tires Nokian i3, mounted on alloy wheels. Summer tires Nokian i3 with an asymmetric tread – the completion of the class of elite tires (UHP). Sale of tires this model, despite the winter weather has already begun – the quality and reliability of the predetermine the tire choice for many car owners in favor of Nokian. Summer tires Nokian i3 made by technology Nordic cool silica compound, which provides using a silicon rubber compound. The result is a high durability, reliability and safety even at high speeds.

Summer tires Nokian i3 claim to be the best in its class. Tires Michelin. Nearly one hundred and ten years of French, Michelin produces winter and summer tires for passenger cars and trucks, planes, and two-wheeler. Michelin tires for sale is all over the world: The company specializes in manufacturing a wide range of products, and therefore can offer the best solution for any car and the road surface. Over the years, Michelin has developed a number of innovative technologies aimed at improving the performance reliability, durability and environmental friendliness of products. As winter and summer tires Michelin made from an exclusive rubber compound with silica, which significantly reduces rolling resistance and therefore allows save fuel. The widespread sale of Michelin tires with a "green" mark allowed the motorists around the world to reduce fuel costs by 3%. Own research and development centers of the company increased the environmental product specifications, resulting in a new winter and summer tires Michelin Energy became the best selling in Europe. This year, the centers will begin selling Michelin tires new "green" models, which reduce rolling resistance by 25%. Another interesting novelty from Michelin – summer tires for passenger cars (the best for alloy wheels), which were developed by technology sport tires together with Porsche and indicators have improved acoustics and vibration.